Bu yüzden birkaç gün önce win7 ile 3 yaşındaki dizüstü bilgisayar oyunculuk yapıyordu (programlar cevap vermiyordu.) Bu yüzden bir chkdsk çalıştırmaya karar verdim, ancak bu bir dosyada durduğundan beri kötü bir fikirdi yaklaşık 24 saat boyunca 4/5 sahnesinde, bad_system_config_info hatasıyla BSOD aldım ve ne zaman şimdi Windows'u başlattığımda, birkaç dakika sonra tamamen tepkisizleşiyor ve zorla kapatmam gerekiyor. Ubuntu'nun taşınabilir bir sürümünü başlattım ve gsmartcontrol'ü çalıştırdım ve sabit disk için şu sonuçları aldım:
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: S2WFPRB7
LU WWN Device Id: 5 000c50 04b0cae93
Firmware Version: 0005HPM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Aug 19 19:42:26 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 070 064 006 Pre-fail Always - 81234683
3 Spin_Up_Time 0x0002 099 098 000 Old_age Always - 0
4 Start_Stop_Count 0x0033 098 098 000 Pre-fail Always - 2202
5 Reallocated_Sector_Ct 0x0033 091 091 036 Pre-fail Always - 201
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 290912486
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10198
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0033 098 098 020 Pre-fail Always - 2115
183 Runtime_Bad_Block 0x0032 100 253 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 34578
188 Command_Timeout 0x0032 100 001 000 Old_age Always - 4295042219
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 046 045 Old_age Always - 34 (Min/Max 25/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 68
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 61
193 Load_Cycle_Count 0x0032 087 087 000 Old_age Always - 27004
194 Temperature_Celsius 0x0022 034 054 000 Old_age Always - 34 (0 10 0 0 0)
195 Hardware_ECC_Recovered 0x001a 048 041 000 Old_age Always - 81234683
196 Reallocated_Event_Count 0x0033 091 091 036 Pre-fail Always - 201
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1846
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 3
SMART Error Log Version: 1
ATA Error Count: 27473 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 27473 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:18.260 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:15.784 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:13.274 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
Error 27472 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:15.784 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:13.274 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
Error 27471 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:10.854 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.288 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.225 READ DMA EXT
Error 27470 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 00:07:08.432 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.358 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.288 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.225 READ DMA EXT
25 00 00 ff ff ff ef 00 00:07:08.166 READ DMA EXT
Error 27469 occurred at disk power-on lifetime: 10196 hours (424 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 9d 00 32 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 01 00 00 00 e0 00 21:58:55.850 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.746 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.642 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.539 IDENTIFY DEVICE
ec 00 01 00 00 00 e0 00 21:58:55.435 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 10198 547053969
# 2 Short offline Completed: read failure 90% 10197 547053969
# 3 Short offline Completed: read failure 90% 10197 547053969
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Bunun ne anlama geldiğini bilmiyorum, çünkü Linux ile tam olarak aşina değilim, yani temelde istediğim şudur: sürücü öldü mü yoksa düzeltilebilir mi? Herhangi bir yardım çok takdir edilecektir!
1
Araba iyi değil. Sürücüden mümkün olduğu kadar fazla veri çekin ve değiştirin.
—
bwDraco
en azından dışarıda, 200 kötü sektör, artı yine çok daha fazlası var .. Ölü olmamanın tek yolu, ona giden gücün berbat olması, sorun yaşamasına neden oluyor.
—
Psycogeek